Rambit Turbocharger for Atari Datarecorders
Back to current versionRestore this version

Rambit Turbocharger for Atari Datarecorders#

The purpose of this interface is to use high transfer rates for compact cassettes which are used with the two models of the 1010 datarecorders and the XC12 (or Phonemark) datarecorder.

The Rambit system consists of a small circuit board containing an IC and a small handful of components, and a tape containing the conversion utility program which is designed to be used either on its own or with an Assembler/Editor cartridge. You will need this cartridge to assist in altering multi-stage load tapes to single stage before converting them to the Rambit format.

The circuit board is easily fitted inside your cassette unit. There are 5 leads to be soldered to the printed circuitry, and my 1010 required that a track be cut and a wire link and capacitor be installed. The instructions give a step-by-step guide, and a diagram of the tracks is supplied to assist in the connection of the leads from the interface board. One black mark, there was no mention of which way round the capacitor should go, but in fact this does not matter. If you prefer, you can have Rambit install this board for you. Without this interface converted programs will not load, and at the moment Rambit will not convert BASIC programs however the interface in no way interferes with normal usage of the cassette unit.

Tapes converted to Rambit format all have a short normal speed boot section at the front of the tape which then controls the loading of the program itself loading it at the incredible speed of 3300-3600 baud. Rambit's loader program loads into Page 0 and the lower half of the stack on Page 1 so that most of the computer's memory can be loaded without fear of overwriting the loader program.

When used in conjunction with an Assembler/Editor cartridge, Rambit will also save assembled machine code in the high-speed format. The resulting tape can be booted in just the same manner as a game, and it will automatically run if you have loaded RUNAD in your code. You are required to include the binary file identification bytes, normally automatically included with your assembled program when saved to tape, so you may prefer to save your code from the Assembler/Editor directly to tape in the normal fashion, and then load it back with Rambit for conversion. The loader program for these binary files loads Page 7 and the lower half of Page 8, and the appropriate loader is automatically added by Rambit.

Rambit's function, then, is to save consecutive areas of memory or single or compound files produced by the Assembler/Editor cartridge at the 3300-3600 baud rate mentioned. Single stage load tapes follow Rambit's conventions already, so converting these is a matter of using the utility's 'L' command to load the original, and the 'S' command to save the converted program to a blank tape. A verification facility allows the checking of the new tape's loading ability. A variety of other commands, many of which bear a close similarity to those in the Assembler/Editor cartridge allow one to display and alter memory.

Multi-stage programs require to be changed to single stage first. The instructions give a guide as to how to do this, but basically you have to use the Assembler/Editor cartridge with the utility to load the first stage in order to locate where the main section is to be loaded and from where it should be done. Once this has been accomplished, the main section is loaded with the 'L' command and then you have to add the boot address information to the start of the program in memory

Flac-files:#

Because the cassette uses the Rambit format, it is not possible to create cas- or atr-files of this tape. You can download the flac-files and record them on a cassette. Rambit_cassette_Side1_V1.flac(info)
Rambit_cassette_Side2_V2.flac(info)

Manual:#

Including schematics for the 1010 and XC12 datarecorders.
Rambit_manual.pdf

Pictures of the interface (click to enlarge):#

Mediapictures:#

Cassette of the Rambit Turbocharger

Thank you#

Many thanks to Page6.org. Parts of the review have been used in this article.