This page (revision-9) was last changed on 03-Feb-2023 15:21 by Roland B. Wassenberg 

This page was created on 28-Aug-2017 14:42 by Fred Meijer

Only authorized users are allowed to rename pages.

Only authorized users are allowed to delete pages.

Page revision history

Version Date Modified Size Author Changes ... Change note
9 03-Feb-2023 15:21 4 KB Roland B. Wassenberg to previous Rambit Turbocharger ==> Rambit Turbocharger for Atari Datarecorders
8 16-Sep-2019 22:51 4 KB Roland B. Wassenberg to previous | to last Rambit Turbocharger for Atari Datarecorders ==> Rambit Turbocharger
7 09-Sep-2019 23:54 4 KB Roland B. Wassenberg to previous | to last
6 09-Sep-2019 23:48 4 KB Roland B. Wassenberg to previous | to last Rambit Turbocharger for Atari Datarecorders2 ==> Rambit Turbocharger for Atari Datarecorders
5 09-Sep-2019 23:48 4 KB Roland B. Wassenberg to previous | to last Rambit Turbocharger for Atari Datarecorders ==> Rambit Turbocharger for Atari Datarecorders2
4 28-Aug-2017 15:01 4 KB Fred Meijer to previous | to last
3 28-Aug-2017 14:47 4 KB Fred Meijer to previous | to last
2 28-Aug-2017 14:44 4 KB Fred Meijer to previous | to last
1 28-Aug-2017 14:42 4 KB Fred Meijer to last

Page References

Incoming links Outgoing links
Rambit Turbocharger for Atari Datarecorders
Rambit Turbocharger for Atari Datarecorders

Version management

Difference between version and

At line 9 changed one line
The circuit board is easily fitted inside your cassette unit. There are 5 leads to be soldered to the printed circuitry, and my 1010 required that a track be cut and a wire link and capacitor be installed. The instructions give a step-by-step guide, and a diagram of the tracks is supplied to assist in the connection of the leads from the interface board. One black mark, there was no mention of which way round the capacitor should go, but in fact this does not matter. If you prefer, you can have Rambit install this board for you. Without this interface converted programs will not load, and at the moment Rambit will not convert BASIC programs however the interface in no way interferes with normal usage of the cassette unit.
The circuit board is easily fitted inside your cassette unit. There are 5 leads to be soldered to the printed circuitry, and the 1010 required that a track be cut and a wire link and capacitor be installed. The instructions give a step-by-step guide, and a diagram of the tracks is supplied to assist in the connection of the leads from the interface board. Without this interface converted programs will not load, and Rambit will not convert BASIC programs however the interface in no way interferes with normal usage of the cassette unit.
At line 13 changed one line
When used in conjunction with an Assembler/Editor cartridge, Rambit will also save assembled machine code in the high-speed format. The resulting tape can be booted in just the same manner as a game, and it will automatically run if you have loaded RUNAD in your code. You are required to include the binary file identification bytes, normally automatically included with your assembled program when saved to tape, so you may prefer to save your code from the Assembler/Editor directly to tape in the normal fashion, and then load it back with Rambit for conversion. The loader program for these binary files loads Page 7 and the lower half of Page 8, and the appropriate loader is automatically added by Rambit.
When used in conjunction with an Assembler/Editor cartridge, Rambit will also save assembled machine code in the high-speed format. The resulting tape can be booted in just the same manner as a game, and it will automatically run if RUNAD is loaded in the code. It is required to include the binary file identification bytes, normally automatically included with the assembled program when saved to tape, so it can be preferred to save the code from the Assembler/Editor directly to tape in the normal fashion, and then load it back with Rambit for conversion. The loader program for these binary files loads Page 7 and the lower half of Page 8, and the appropriate loader is automatically added by Rambit.
At line 15 changed one line
Rambit's function, then, is to save consecutive areas of memory or single or compound files produced by the Assembler/Editor cartridge at the 3300-3600 baud rate mentioned. Single stage load tapes follow Rambit's conventions already, so converting these is a matter of using the utility's 'L' command to load the original, and the 'S' command to save the converted program to a blank tape. A verification facility allows the checking of the new tape's loading ability. A variety of other commands, many of which bear a close similarity to those in the Assembler/Editor cartridge allow one to display and alter memory.
Rambit's function is to save consecutive areas of memory or single or compound files produced by the Assembler/Editor cartridge at the 3300-3600 baud rate mentioned. Single stage load tapes follow Rambit's conventions already, so converting these is a matter of using the utility's 'L' command to load the original, and the 'S' command to save the converted program to a blank tape. A verification facility allows the checking of the new tape's loading ability. A variety of other commands, many of which bear a close similarity to those in the Assembler/Editor cartridge allow one to display and alter memory.
At line 17 changed one line
Multi-stage programs require to be changed to single stage first. The instructions give a guide as to how to do this, but basically you have to use the Assembler/Editor cartridge with the utility to load the first stage in order to locate where the main section is to be loaded and from where it should be done. Once this has been accomplished, the main section is loaded with the 'L' command and then you have to add the boot address information to the start of the program in memory
Multi-stage programs require to be changed to single stage first. The instructions give a guide as to how to do this, but basically you have to use the Assembler/Editor cartridge with the utility to load the first stage in order to locate where the main section is to be loaded and from where it should be done. Once this has been accomplished, the main section is loaded with the 'L' command and then you have to add the boot address information to the start of the program in memory.
At line 19 changed one line
!!Flac-files:
!!Flac-files
At line 24 changed one line
!!Manual:
!!Manual
At line 28 changed one line
!!Pictures of the interface (right-click to save the larger images):
!!Pictures of the interface (right-click to save the larger images)
At line 33 changed one line
!!Mediapictures:
!!Mediapictures
This page (revision-9) was last changed on 03-Feb-2023 15:21 by Roland B. Wassenberg  Top